Microscopy Skills: Getting a Reliable Peripheral Smear Every Time

Ask a pathologist what wastes their time and poorly made smears will be near the top. Not difficult cases — badly spread films, over-stained films, films with no readable area at all.

The frustrating part is that making a good one is not hard. It is a technique with about five variables, all of them controllable, and once someone shows you properly it takes a week to become consistent.

## Start with the drop

Small. Smaller than instinct suggests — roughly 2 to 3 microlitres, which is a drop you would describe as disappointing.

Too large a drop is the single most common cause of a bad film. It produces a thick smear that runs off the end of the slide, with no feathered edge and no monolayer, and no amount of skill at the microscope rescues it.

Place it about a centimetre from one end, and work quickly. From an EDTA tube, mix thoroughly first — a well-mixed sample, inverted gently several times, not a tube that has been sitting.

Ideally make the film within an hour of collection. EDTA storage artefact develops after a few hours: cells crenate, neutrophils become hypersegmented in appearance, and morphology becomes unreliable.

## The spread

Bring the spreader slide back into the drop at roughly a 30 to 45 degree angle and wait for the blood to run along the contact line. Then push forward in one smooth movement, all the way off the end.

Three things to get right.

Angle controls thickness. Steeper gives a shorter, thicker film; shallower gives a longer, thinner one. Anaemic blood is less viscous and spreads further, so use a steeper angle. Polycythaemic blood needs a shallower one. Adjusting the angle to the sample is what separates someone who makes good films from someone who makes good films only from normal samples.

Speed should be smooth and moderate. Hesitation produces ridges and lines across the film.

The edge of the spreader must be smooth and clean. A chipped spreader leaves streaks in exactly the same place every time, and people replace the technique when they should replace the slide.

A well-made film occupies about two-thirds of the slide, has a smooth feathered tail, and shows no holes, ridges or lines.

## Drying and staining

Air dry rapidly and completely. Waving it gently is fine. A film that is still damp when it meets fixative shows water artefact — red cells with refractile centres that can be mistaken for parasites.

Do not heat fix.

For staining, the two things that go wrong are stain age and buffer pH. Romanowsky stains need buffer near pH 6.8, and drift toward acid gives red cells that are too pink with pale nuclei, while alkaline drift gives everything a heavy blue cast. If your films have gradually shifted colour over months, check the buffer before blaming the stain.

Filter the stain and change it on a schedule based on slide count rather than on how it looks. Stain deposit on the film is a common finding and it looks, at a glance, uncomfortably like bacteria or platelet debris.

## Finding the reading area

Not the thick end, where cells overlap. Not the extreme tail, where they distort and where larger cells accumulate.

The reading zone is where red cells just touch without overlapping, a little back from the feathered edge. Learn to find it at 10x before switching to oil, because scanning at low power first also lets you spot rouleaux, platelet clumps and large abnormal cells that migrate to the edges.

Any competent microscope makes this straightforward — a Labomed LX 300 or Olympus CX23 with clean oil-immersion optics is entirely adequate. Set the condenser properly. A poorly adjusted condenser costs you resolution that no objective can give back.

## Make two

It costs a minute and it saves a repeat sample. Films get broken, over-stained, or wanted for a special stain later, and there is no way to obtain more film from a sample that has since clotted or aged.

For students: this is a manual skill, which means it improves with deliberate practice and decays without it. Make films from every sample you can while somebody is available to tell you what is wrong with them.

Have a question about lab equipment?

Our team is happy to help you choose the right instrument for your lab.

WhatsApp Us